Is a sensor included with the wire?

Name: Schluter DITRA-HEAT-E-HK Cable - 120V
Brand: Schluter
SKU: DITRAHEAT 120V CABLE
Price: 224.16 USD
Availability: InStock

No, the sensor wire is included with the Thermostats.

Schluter DITRA-HEAT-E-HK Cable

The 120V Schluter Ditra Heat Cables (DITRA-HEAT-E-HK) are a twisted pair heating cable designed for integration with DITRA-HEAT Uncoupling Membrane in interior floor warming applications.

Schluter DITRA HEAT E HK 120V Floor Warming Cable Features:

Cables snap into the membrane; clips and fasteners are not required
No self-levelers required to encapsulate the cables; installation time significantly reduced
No return to thermostat required
Produces virtually zero electromagnetic fields
120V and 240V options available in a variety of lengths

Important Schluter Ditra Heat Cable Ordering Information

Do not purchase a heating cable the same size as the area to be tiled; this will be too much heating cable!
Very important: Never CUT the heating cable. This would change the cable resistance and could lead to a fire.
Install the heating cable at a spacing of 3 studs (3-1/2" – 9 cm).
Minimum spacing from walls or fixtures (e.g., cabinets) is 3" (75 mm).
Minimum spacing from other heat sources (baseboard heaters, fireplaces, forced air heating ducts, etc.) is 8" (200 mm)
Minimum spacing from any plumbing drain is 6" (150 mm).
The heating cable section of the cable must be entirely installed under the floor covering. In order to prevent a fire hazard, do not install it anywhere else (e.g., in a wall).
Never install heating cable under vanities, bathtub platforms, kitchen cabinets and islands or any other fixtures. Excessive heat could build up in these confined spaces and may cause a fire.
It is helpful to plan the location of a buffer zone, as it is not possible to predict where the heating cable will end. The buffer zone is an area where heating is not essential, typically behind a toilet or adjacent to a door opening. This area allows for placement of excess heating cable.
Heating cable testing is required while the heating cable is on the spool and at two subsequent steps during installation to ensure cable quality and for warranty purposes. A megohmmeter is required for the insulation resistance testing of the heating cables.

Schluter DITRA-HEAT-E-HK 120V Floor Warming Cable Specifications:

Item No	Heating Cable Length (ft)	Area Covered per Cable Spacing		Total Power (W)	Avg. Power per Unit Area per Cable Spacing		Current (Amps)
Item No	Heating Cable Length (ft)	Regular 3 Stud (sq.ft)	Alternating 3-2 Stud (sq.ft)	Total Power (W)	Regular 3 Stud (Watts/sq.ft)	Alternating 3-2 Stud (Watts/sq.ft)	Current (Amps)
DHEHK12011	35.3	10.7	8.9	135	12.6	15.2	1.1
DHEHK12016	52.9	16.0	13.3	203	12.7	15.2	1.7
DHEHK12021	70.5	21.3	17.8	270	12.7	15.2	2.3
DHEHK12027	88.2	26.7	22.2	338	12.7	15.2	2.8
DHEHK12032	105.8	32.0	26.7	405	12.7	15.2	3.4
DHEHK12038	124.1	37.5	31.3	475	12.7	15.2	4.0
DHEHK12043	141.1	42.7	35.6	540	12.7	15.2	4.5
DHEHK12051	169.8	51.4	42.8	650	12.7	15.2	5.4
DHEHK12064	212.9	64.4	53.7	815	12.7	15.2	6.8
DHEHK12073	240.2	72.7	60.6	920	12.7	15.2	7.7
DHEHK12083	275.5	83.3	69.4	1055	12.7	15.2	8.8
DHEHK12092	303.0	91.7	76.4	1160	12.7	15.2	9.7
DHEHK120102	336.9	101.9	84.9	1290	12.7	15.2	10.7
DHEHK120113	372.2	112.6	93.8	1425	12.7	15.2	11.9
DHEHK120134	444.0	134.3	111.9	1700	12.7	15.2	14.2

Download KERDI-DRAIN Installation Handbook
Download Ditra Heat Calculation sheet
Download Ditra Heat Data Sheet
Download Schluter Ditra Heat Brochure

SKU	DITRAHEAT 120V CABLE
Non-Returnable	No
Manufacturer	Schluter
Warranty	Limited 10 Year Warranty
Voltage	120
Weight (lbs.)	3.02 - 13.45
Dimensions (L x W x H)	13" x 12" x 4"