Laticrete Hydro Ban Preformed Triangle Seat

Laticrete Hydro Ban Preformed Triangle Seat
Laticrete Hydro Ban Preformed Triangle Seat
$102.00
From $102.00 to $136.11

* Required Fields

Product Description

PRODUCT DESCRIPTION

LATICRETE Hydro Ban Preformed Seat are components of the expanded LATICRETE Hydro Ban line of products that allow for high quality rapid shower installations. LATICRETE Hydro Ban Preformed Seat are made from high-density expanded polystyrene with a waterproof coating. The LATICRETE Hydro Ban Preformed Seats are 100% waterproof and ready-to-tile. Materials: LATICRETE polymer fortified medium bed mortar mix for leveling pan area, 1/2" x 1/2" (12 mm x 12 mm) square notched trowel, LATICRETE polymer fortified thin-set and LATICRETE Hydro Ban Adhesive & Sealant.

Advantages

  • Lightweight and durable easy to transport, handle and adjust during installation.
  • Factory installed, code approved waterproofing meets ANSI A1 118.10 requirements.
  • Ready to tile!
  • Multiple design options and sizes available adding utility and value to the shower installation.
  • Component of LATICRETE Lifetime Warranty* Single source responsibility.
  • Works in conjunction LATICRETE tile and stone installation materials. * See DS 230.99 for complete warranty information

  • Uses

  • Interior use only.
  • Swimming pools, fountains and water features.
  • Shower stalls and tub surrounds.
  • Industrial, commercial and residential. Suitable Substrates
  • Concrete
  • Cement backer board **
  • Cement mortar beds
  • Pre-Sloped shower pans
  • Ceramic Tile or Stone

  • ** Consult cement backer board manufacturer for specific installation recommendations and to verify acceptability for exterior use.

    Packaging

    All LATICRETE Hydro Ban Preformed Seats are 20" (51 mm) in height

    16" x 16" (41 cm x 41 cm) Triangle
    23" x 23" (58 cm x 58 cm) Triangle
    16" x 16" (41 cm x 41 cm) Triangle Convex

    Shelf Life

    Factory sealed containers of this product are guaranteed to be of first quality for Five (5) years if stored at temperatures >32°F (0°C) and <110°F (43°C).

    Limitations

  • Adhesives/mastics, mortars and grouts for ceramic tile, pavers, brick and stone are not replacements for waterproofing membranes. When a waterproofing membrane is required, use LATICRETE Hydro Ban.
  • Note: Surfaces must be structurally sound, stable and rigid enough to support ceramic/stone tile, thin brick and simi lar finishes. Substrate deflection under all live, dead and impact loads, including concentrated loads, must not exceed L/360 for thin bed ceramic tile/brick installations or L/480 for thin bed stone installations and L/600 for all exterior veneer applications where L=span length.
  • Do not expose unprotected LATICRETE Hydro Ban Preformed Seat to sun or weather for more than 30 days.
  • Do not expose to rubber solvents or ketones.
  • Must be covered with ceramic tile, stone, finish. Use protection board for temporary cover prior to finishing.

  • Cautions

    Consult MSDS for more safety information.

  • During cold weather, protect finished work from traffic until fully cured.
  • For white and light-colored marbles, use a white LATICRETE Latex Portland Cement Thin Set Mortar.
  • For green and moisture sensitive marble, agglomerates and resin backed tile and stone use LATAPOXY® 300 Adhesive (refer to Data Sheet 633.0).
  • If the waterproof coating on the LATICRETE Hydro Ban Preformed Seat is punctured during installation or from job site construction activity recoat the punctured area and 2" (50 mm) around the area with two coats of LATICRETE Hydro Ban, follow DS 663.0 and DS 663.5 for full instructions.
  • Product Specifications

    SKU: l-bench
    Manufacturer: Laticrete
    Warranty: Limited Warranty Upon Manufacturer Inspection

    Product Questions & Answers

    + Add Your Review

    How do you rate this product? *

      1 star 2 stars 3 stars 4 stars 5 stars
    Overall